| Viewing Posts Made On March 11th 2010 |
| Message |
Posted |
Forum |
Topic: What is the relationship between 0 and defpoints?
Posted by: cjehly
|
I still, to this day, will throw a VP up on Defpoints on occasion. Its the reb ...
|
|
02:56:41 |
General Discussions... |
Topic: What is the relationship between 0 and defpoints?
Posted by: fishandchips
|
The factory recommends (implicitly) using noplot layers rather than defpoints.
|
|
07:12:05 |
General Discussions... |
Topic: Bad Plans?
Posted by: fishandchips
|
Looks like a good case for IPD only.
|
|
07:13:56 |
General Discussions... |
Topic: Changing Pipe Size
Posted by: fishandchips
|
Remember if changing one stick/fitting at a time to use the pulldown to select t ...
|
|
07:16:15 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: Use of non-standard straight
Posted by: fishandchips
|
Since cost per is greater for a table piece than a coil line piece by a factor o ...
|
|
07:18:42 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: Use of non-standard straight
Posted by: tnbndr
|
[quote]
fishandchipsSince cost per is greater for a table piece than a coil line ...
|
|
11:52:02 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: Bad Plans?
Posted by: VirtualPilot
|
I always cringe when I get drawings that are done single line.... those 99% of t ...
|
|
12:59:20 |
General Discussions... |
Topic: ESJ or MAJ
Posted by: TFuller
|
I've always used a .maj. I believe it might be database related and I believe I ...
|
|
13:00:47 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: What is the relationship between 0 and defpoints?
Posted by: VirtualPilot
|
[quote=TFuller]It is.
Okay, sorry for the tangent on this post. I restarted ACA ...
|
|
13:03:26 |
General Discussions... |
Topic: Change Object(s) Properties no-no...
Posted by: VirtualPilot
|
That was a huge problem as the CAM side did not noticed this happening and we ha ...
|
|
13:09:35 |
General Bug Reports |
Topic: Who are you?
Posted by: TFuller
|
Maybe I should have done this earlier.
Thomas N Fuller II
CAD-Duct Detailer / C ...
|
|
13:13:08 |
Introductions... |
Topic: ESJ or MAJ
Posted by: VirtualPilot
|
We have never ever used a ESJ and don't understand why you would want to create ...
|
|
13:13:18 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: ESJ or MAJ
Posted by: astclair
|
I can say from an estimating standpoint EST Duct or EST Mech it's very important ...
|
|
13:13:25 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: Rotated p-traps
Posted by: Bobby T
|
Does anyone know the setting that controls the way p-traps are brought in when u ...
|
|
13:42:37 |
Designline |
Topic: Straight Duct
Posted by: Cadana
|
Now saying that the duct is named machine cut and the full length is to the coil ...
|
|
13:55:31 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: Straight Duct
Posted by: cam-nav
|
This is a setup in the above mentioned "Straights" button, uncheck the "4-Part A ...
|
|
14:07:29 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: CAD-Duct not showing in Navis...yet another ebabler issue here I guess
Posted by: bparrell
|
Can you tell use which loader is it using or the Acad software?The .dll seems to ...
|
|
14:12:37 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: JR Smith Floor Drains and Clean outs
Posted by: SOstendorf
|
Does anyone have JR Smith 2005L Floor drains and 4031 series clean outs that are ...
|
|
14:31:15 |
XtraCAD Swap Shop... |
Topic: Metric !
Posted by: Cadana
|
Anyone on this system successfully detailing in metric and sending to the shop a ...
|
|
14:51:40 |
CAD-Duct Solids/CAD-Mech Users... |
Topic: Rotated p-traps
Posted by: cadbyken
|
See if this helps
http://www.xtracad.com/forum/viewtopic.php?id=4773
|
|
14:57:55 |
Designline |
|
|
Powered by PunBB
© Copyright 2002-2007 Rickard Andersson
|
|
