« previous next »
Pages: [1]   Go Down

Author Topic: Item set to Machine Cut, but Nothing to nest  (Read 384 times)

0 Members and 1 Guest are viewing this topic.

Offline patrydufTopic starter

  • Premier Member
  • *****
  • Posts: 1145
  • Country: ca
  • Gender: Male
Item set to Machine Cut, but Nothing to nest
« on: Nov 04, 2025, 16:55:38 PM »
I have this CID#311 set to machine Cut.
The automatic Nest returns "Nothing to Nest".
There is "-" in the job content under the column "Nested".
I think I looked everywhere, but obviously not!
I had a friend send me his CID#311 and it worked.
What was the problem with the other part? It was taken in the V7.05 folder.
Is there a lock, or something on certain items coming from ADSK?
Thanks for your help.
Logged
"Whether you think you can or you can't - YOU'RE RIGHT."
"Que vous croyiez pouvoir ou non - VOUS AVEZ RAISON."

Yvon Dufresne - Novybec
CADmep, CAMduct, Revit, eVolve

Offline Jona

  • Senior Member
  • ****
  • Posts: 282
  • Country: us
  • Gender: Male
Re: Item set to Machine Cut, but Nothing to nest
« Reply #1 on: Nov 04, 2025, 18:48:22 PM »
Things I found that could give me the same "-" Nested Result :

1) "Not Cut" was selected on each part of the development or
2) On the Options tab 8 and 9 being set to No Pipe and No Branch or
3) no material was assigned

Hopefully one of those is your solution.
Logged

Offline patrydufTopic starter

  • Premier Member
  • *****
  • Posts: 1145
  • Country: ca
  • Gender: Male
Re: Item set to Machine Cut, but Nothing to nest
« Reply #2 on: Nov 04, 2025, 18:54:00 PM »
Thank you Jona,
 All of those are OK, but still nothing to nest.
That's why I was looking for some hidden "lock" option from deep within.
Logged
"Whether you think you can or you can't - YOU'RE RIGHT."
"Que vous croyiez pouvoir ou non - VOUS AVEZ RAISON."

Yvon Dufresne - Novybec
CADmep, CAMduct, Revit, eVolve

Offline ThatCadGuy

  • Active Member
  • **
  • Posts: 26
  • Country: us
  • Gender: Male
Re: Item set to Machine Cut, but Nothing to nest
« Reply #3 on: Nov 06, 2025, 13:19:49 PM »
Did you make sure the item isn't flagged to be bought?
Logged

Offline patrydufTopic starter

  • Premier Member
  • *****
  • Posts: 1145
  • Country: ca
  • Gender: Male
Re: Item set to Machine Cut, but Nothing to nest
« Reply #4 on: Nov 06, 2025, 13:49:02 PM »
Good point.
I'll tcheck that...
Logged
"Whether you think you can or you can't - YOU'RE RIGHT."
"Que vous croyiez pouvoir ou non - VOUS AVEZ RAISON."

Yvon Dufresne - Novybec
CADmep, CAMduct, Revit, eVolve

Offline Dean-o

  • Full Member
  • ***
  • Posts: 78
  • Country: us
  • Gender: Male
Re: Item set to Machine Cut, but Nothing to nest
« Reply #5 on: Nov 17, 2025, 16:01:48 PM »
On two separate occasions, I had parts that show as nested, but they are NOT nested. The funny thing is that I can just open them up and accept, and they are then nestable. I don't have to change a thing, just accept them and there they are. This is totally random
Logged
Pages: [1]   Go Up
« previous next »