...serving the BIM community since 2003
| The number one site for CADmep™ ESTmep™ and CAMduct™ users... | |
| including additional topics and discussions covering AutoCAD®, Navisworks®, Revit®, GTP Stratus, and much more |
|
 |
Started in 2003, XtraCAD.com was set up as a platform to aid users of the newly evolving range of 3D parametric modelling software utilities being developed by Micro Application Packages (MAP) from Blackpool, England. Throughout the continual development of these applications, including the acquisition of MAP by Autodesk® in 2011 and subsequent rebranding, we have remained the first port of call for many users of all levels seeking assistance. We are proud that Autodesk 'fully understand the importance of XtraCAD for the CADmep and Fabrication community' and acknowledge that we 'do a great service by maintaining this community and understand it is important for users'. Join us now and become a part of the future of Building Services Coordination & BIM. |
|
EU Law: By signing in to this site I agree that XtraCAD.com may set cookies on my browser.
Dec 10, 2025, 17:12:47 PM by Dean-o | Views: 41 | Comments: 0
Hello all. I have just been informed that we will be purchasing a gorelocker. I haven't dove too deep into this previously as I was under the impression that this might not happen very soon. I can pos... Dec 05, 2025, 14:29:41 PM by dfiorini | Views: 245 | Comments: 7
Wondering if anyone has found a good solution for nesting spiral duct to minimize waste? Dec 03, 2025, 20:39:15 PM by cduncan11 | Views: 141 | Comments: 0
Has anyone experienced this issue and found a solution? When I try to install the Trimble Fabshop Export add in for CADmep I get an error that says I do not have CADmep installed. However, I currently... Nov 27, 2025, 14:00:39 PM by b.kata | Views: 259 | Comments: 3
Hi, We are working with a database that doesn't have a prodinfo.map file set up. After looking through some topics on the forum, it seems to me that while populating the database, you shou... Nov 25, 2025, 20:17:06 PM by Mtt849 | Views: 192 | Comments: 1
I cant seem to get a notch to populate on Pittsburg Male or female at locations of str/or change of direction. Pages: [1]
|
Guests: 150
Total Members: 
|
Spiral Duct nesting Software Add-on to Minimize waste
[General Discussions] |
DotNet Dec 10, 2025, 21:12:48 PM |
|
|
Notch angle for seams on round fittings
[CAMduct™ Users] |
Dean-o Dec 10, 2025, 17:12:47 PM |
|
|
Item Quantities in my worksheet
[CADmep™ Worksheets & Reports] |
cadbob Dec 09, 2025, 13:40:18 PM |
|
|
Show Service is Grayed out
[Fabrication Parts in Revit®] |
cgurzi Dec 04, 2025, 23:44:09 PM |
|
|
Double Wall Construction
[CAMduct™ Users] |
Rknoch Dec 04, 2025, 21:07:56 PM |
Recent Posts
Re: Spiral Duct nesting Software Add-on to Minimize waste by DotNet
[Dec 10, 2025, 21:12:48 PM]
Re: Spiral Duct nesting Software Add-on to Minimize waste by DotNet
[Dec 10, 2025, 21:03:07 PM]
Notch angle for seams on round fittings by Dean-o
[Dec 10, 2025, 17:12:47 PM]
Re: Spiral Duct nesting Software Add-on to Minimize waste by dfiorini
[Dec 09, 2025, 18:06:44 PM]
Re: Spiral Duct nesting Software Add-on to Minimize waste by cadbob
[Dec 09, 2025, 13:41:01 PM]
[Dec 10, 2025, 21:12:48 PM]
Re: Spiral Duct nesting Software Add-on to Minimize waste by DotNet
[Dec 10, 2025, 21:03:07 PM]
Notch angle for seams on round fittings by Dean-o
[Dec 10, 2025, 17:12:47 PM]
Re: Spiral Duct nesting Software Add-on to Minimize waste by dfiorini
[Dec 09, 2025, 18:06:44 PM]
Re: Spiral Duct nesting Software Add-on to Minimize waste by cadbob
[Dec 09, 2025, 13:41:01 PM]
From here you may access additional areas of the site..