...serving the BIM community since 2003
| The number one site for CADmep™ ESTmep™ and CAMduct™ users... | |
| including additional topics and discussions covering AutoCAD®, Navisworks®, Revit®, GTP Stratus, and much more |
|
 |
Started in 2003, XtraCAD.com was set up as a platform to aid users of the newly evolving range of 3D parametric modelling software utilities being developed by Micro Application Packages (MAP) from Blackpool, England. Throughout the continual development of these applications, including the acquisition of MAP by Autodesk® in 2011 and subsequent rebranding, we have remained the first port of call for many users of all levels seeking assistance. We are proud that Autodesk 'fully understand the importance of XtraCAD for the CADmep and Fabrication community' and acknowledge that we 'do a great service by maintaining this community and understand it is important for users'. Join us now and become a part of the future of Building Services Coordination & BIM. |
|
EU Law: By signing in to this site I agree that XtraCAD.com may set cookies on my browser.
Yesterday at 14:36:22 by aleschper | Views: 15 | Comments: 0
Is anyone else having issues with end notches being applied differently in CAM/CAD 2025 than they are in the 2023 versions? Our setting in the 2023 software work perfectly, but when we were tryin... Feb 13, 2026, 15:39:38 PM by RMrog | Views: 353 | Comments: 5
Hello, I am trying to connect round duct to oval duct but am having connector issues. First of all, is this even possible? I don't see a way to switch C1/C2 from round to oval in the drop d... Feb 10, 2026, 17:34:34 PM by cyan | Views: 294 | Comments: 2
Considering I've seen this issue at more than one place, I'm sure this has been asked before and my search skills have been found lacking. For this, I apologize. I'm going to ask anyway. Feb 09, 2026, 19:05:43 PM by DamCam | Views: 257 | Comments: 0
Does anyone have cover sheet from reports they would be willing to share. i am envisioning job#s, due date's, check list's, Etc.... Feb 09, 2026, 17:50:21 PM by DamCam | Views: 238 | Comments: 0
Is anyone using the Vicon 1.5 20" laser table with clean air? Pages: [1]
|
Guests: 360
Facebook (10)
Total Members: 
|
Large End to Small End Round Fittings
[CAMduct™ Users] |
cyan Today at 01:53:03 |
|
|
Using pattern 2199
[CADmep™ Users] |
WilliamNY Yesterday at 21:51:46 |
|
|
Nest Liner Only
[CAMduct™ Users] |
aleschper Yesterday at 14:39:33 |
|
|
2025 and 2023 Notch Calculations
[CAMduct™ Users] |
aleschper Yesterday at 14:36:22 |
|
|
Round to Oval Connectors
[CADmep™ Users] |
VirtualPilot Feb 17, 2026, 20:22:42 PM |
Recent Posts
Re: Large End to Small End Round Fittings by cyan
[Today at 01:53:03]
Re: Using pattern 2199 by WilliamNY
[Yesterday at 21:51:46]
Re: Nest Liner Only by aleschper
[Yesterday at 14:39:33]
2025 and 2023 Notch Calculations by aleschper
[Yesterday at 14:36:22]
Re: Large End to Small End Round Fittings by aleschper
[Yesterday at 14:31:33]
[Today at 01:53:03]
Re: Using pattern 2199 by WilliamNY
[Yesterday at 21:51:46]
Re: Nest Liner Only by aleschper
[Yesterday at 14:39:33]
2025 and 2023 Notch Calculations by aleschper
[Yesterday at 14:36:22]
Re: Large End to Small End Round Fittings by aleschper
[Yesterday at 14:31:33]
From here you may access additional areas of the site..