...serving the BIM community since 2003
| The number one site for CADmep™ ESTmep™ and CAMduct™ users... | |
| including additional topics and discussions covering AutoCAD®, Navisworks®, Revit®, GTP Stratus, and much more |
|
 |
Started in 2003, XtraCAD.com was set up as a platform to aid users of the newly evolving range of 3D parametric modelling software utilities being developed by Micro Application Packages (MAP) from Blackpool, England. Throughout the continual development of these applications, including the acquisition of MAP by Autodesk® in 2011 and subsequent rebranding, we have remained the first port of call for many users of all levels seeking assistance. We are proud that Autodesk 'fully understand the importance of XtraCAD for the CADmep and Fabrication community' and acknowledge that we 'do a great service by maintaining this community and understand it is important for users'. Join us now and become a part of the future of Building Services Coordination & BIM. |
|
Lá fhéile Pádraig sona dhaoibh!
 Happy St. Patrick's Day Enjoy the Guinness!
|
EU Law: By signing in to this site I agree that XtraCAD.com may set cookies on my browser.
Mar 12, 2026, 18:19:45 PM by Mtt849 | Views: 155 | Comments: 1
Got an odd issue. If I draw a duct size over 78" or under 111" that is less than a standard length, I get the error in the attached snip? 112" duct size and larger it does not d... Mar 09, 2026, 15:01:28 PM by msheofsky | Views: 260 | Comments: 1
I've made a decoiled straight report. I have the total area for the pieces of duct and the actual area used. I want my report to add it all up by gauge. I have the following in my report to build i... Mar 06, 2026, 20:39:33 PM by jimbon | Views: 265 | Comments: 0
How does one find the correct Post Processor for a given table? Is it really just trial and error? It is a PPI machine, but the PPI Post Processor in CAMduct does not create the same code ... Mar 05, 2026, 15:10:53 PM by VirtualPilot | Views: 342 | Comments: 0
I noticed 2026 creating horrible looking icons now, they used to look good before with thin outer lines, now they are thick and horribly looking, is there a setting I'm missing? Mar 04, 2026, 15:41:21 PM by Engelhab123 | Views: 339 | Comments: 0
I'm looking for ways to adjust how many pieces to cut sheet metal parts (shoe taps, straight joints, etc...) based on specific parameters like overall stretchout or if it's lined. We primarily draw in... Pages: [1]
|
Guests: 3262
Yandex
Total Members: 
|
Virtual Mechanical Section
[General Discussions] |
Hess17 Mar 13, 2026, 10:47:18 AM |
|
|
Duct sizes over 78" / under 112" only come in as standard length-Error if not
[CAMduct™ Users] |
cyan Mar 12, 2026, 22:25:13 PM |
|
|
CAMduct Report adding up total area by gauge
[CADmep™ Users] |
AN-detail Mar 10, 2026, 13:58:12 PM |
|
|
Large End to Small End Round Fittings
[CAMduct™ Users] |
cyan Mar 07, 2026, 18:30:33 PM |
|
|
Finding the Right Post Processor - I and J Code issue
[CAMduct™ Users] |
jimbon Mar 06, 2026, 20:39:33 PM |
Recent Posts
Re: Virtual Mechanical Section by Hess17
[Mar 13, 2026, 10:47:18 AM]
Re: Duct sizes over 78" / under 112" only come in as standard length-Error if not by cyan
[Mar 12, 2026, 22:25:13 PM]
Duct sizes over 78" / under 112" only come in as standard length-Error if not by Mtt849
[Mar 12, 2026, 18:19:45 PM]
Re: CAMduct Report adding up total area by gauge by AN-detail
[Mar 10, 2026, 13:58:12 PM]
CAMduct Report adding up total area by gauge by msheofsky
[Mar 09, 2026, 15:01:28 PM]
[Mar 13, 2026, 10:47:18 AM]
Re: Duct sizes over 78" / under 112" only come in as standard length-Error if not by cyan
[Mar 12, 2026, 22:25:13 PM]
Duct sizes over 78" / under 112" only come in as standard length-Error if not by Mtt849
[Mar 12, 2026, 18:19:45 PM]
Re: CAMduct Report adding up total area by gauge by AN-detail
[Mar 10, 2026, 13:58:12 PM]
CAMduct Report adding up total area by gauge by msheofsky
[Mar 09, 2026, 15:01:28 PM]
From here you may access additional areas of the site..