The number one site for CADmep ESTmep and CAMduct users...
including additional topics and discussions covering AutoCAD®, Navisworks®, Revit®, and much more
Started in 2003, XtraCAD.com was set up as a platform to aid users of the newly evolving range of 3D parametric modelling software utilities being developed by Micro Application Packages (MAP) from Blackpool, England.

Throughout the continual development of these applications, including the acquisition of MAP by Autodesk® in 2011 and subsequent rebranding, we have remained the first port of call for many users of all levels seeking assistance.

We are proud that Autodesk 'fully understand the importance of XtraCAD for the CADmep and Fabrication community' and acknowledge that we 'do a great service by maintaining this community and understand it is important for users'.

Join us now and become a part of the future of Building Services Coordination & BIM.

* Who's Online

  • Dot Guests: 12
  • Dot Spiders: 0
  • Dot Hidden: 0
  • Dot Users: 3
  • Dot Users Online:

* Board Stats

  • stats Total Members: 5020
  • stats Total Posts: 102171
  • stats Total Topics: 15120
  • stats Total Categories: 10
  • stats Total Boards: 35
  • stats Most Online: 324
Registered on XtraCAD but account not yet approved?

After registering an email will have been sent to you. Please check ALL the email accounts that you submitted when registering to ensure that it is not in your spam box. We could be waiting for a response from you.
EU Law: By signing in to this site I agree that XtraCAD.com may set cookies on my browser.

* Latest Job Opportunities

Drafting/BIM Coordinator Required, Carol Stream, Illinois...
coordination and shop drawings for small to large... specific BIM meetings... take offs and listing for... working with AutoCAD with a mechanical... assisting project... for further details CLICK HERE.

Today at 06:15:51 PM by jaysomlam | Views: 33 | Comments: 2

I would like to get some info about Tracker.  I don't know which forum that I should post this message.  I figure CAMduct forum should be a good place to post because we cannot track something that ha...
Today at 03:25:39 PM by WilliamNY | Views: 46 | Comments: 2

I'm sure someone has already done this. I'm looking to be able to run a report (.csf) from the command line. For example, when I run ADDREPORT from the command line, even if FILEDIA is set to 0, it st...
Today at 02:48:01 PM by DodgemanT120RV | Views: 26 | Comments: 1

I am doing a project where I have plumbing and process piping. I need to run material lists for both and want to have the reports sorted by system then size. I can't figure how to set it up. Can anyon...
Today at 03:00:23 AM by tinbasher | Views: 44 | Comments: 2

Hi all, I’ve used CAMDuct a bit at a job about 4 years ago. I’m running the free trial and wondering how You can browse all HVAC rectangular round and multi shaped CIDs. I recall there were over 900, ...
Yesterday at 03:00:11 PM by david d | Views: 44 | Comments: 2

Hello,
Im really hoping that someone on this site can help me out with this issue. Not only does the problem occur with square to rounds but with Pipe reducers as well.
In my shop we turn a ...
Pages: [1]

* Recent Posts

Re: Square to round fittings collar too tight by david d
[Today at 09:18:25 PM]


Re: Need Info on Tracker by dbanker
[Today at 09:00:47 PM]


Re: Piping and Plumbing Reports by cadragon
[Today at 08:38:23 PM]


Re: Need Info on Tracker by DotNet
[Today at 07:01:24 PM]


Re: Create a report from the command line? by WilliamNY
[Today at 06:49:58 PM]