The number one site for CADmep™ ESTmep™ and CAMduct™ users...
including additional topics and discussions covering AutoCAD®, Navisworks®, Revit®, GTP Stratus, and much more
Started in 2003, XtraCAD.com was set up as a platform to aid users of the newly evolving range of 3D parametric modelling software utilities being developed by Micro Application Packages (MAP) from Blackpool, England.

Throughout the continual development of these applications, including the acquisition of MAP by Autodesk® in 2011 and subsequent rebranding, we have remained the first port of call for many users of all levels seeking assistance.

We are proud that Autodesk 'fully understand the importance of XtraCAD for the CADmep and Fabrication community' and acknowledge that we 'do a great service by maintaining this community and understand it is important for users'.

Join us now and become a part of the future of Building Services Coordination & BIM.

* Who's Online

  • Dot Guests: 28
  • Dot Spiders: 18
  • Dot Hidden: 0
  • Dot Users: 0
  • Dot Users Online:
  • user Yandex (11)
  • user Google (4)
  • user Bing (2)
  • user AppleBot

* Board Stats

  • stats Total Members: 5615
  • stats Total Posts: 111100
  • stats Total Topics: 16848
  • stats Total Categories: 10
  • stats Total Boards: 37
  • stats Most Online: 859
Registered on XtraCAD but account not yet approved?

After registering an email will have been sent to you. Please check ALL the email accounts that you submitted when registering to ensure that it is not in your spam box. We could be waiting for a response from you.
EU Law: By signing in to this site I agree that XtraCAD.com may set cookies on my browser.

clipCID #866 and #1 - Straight Type

May 26, 2023, 13:55:54 PM by ayoung8901 | Views: 63 | Comments: 0
Hi all,

I searched the forum and cannot seem to find this question.

I am curious if there is a way to make straight duct to automatically change from 1pc, Wrapper, 2pc, 4pc? I kn...
Read More | Write Comment

xxEvolve Point on Invert of Pipe

May 26, 2023, 13:46:19 PM by welchy78 | Views: 81 | Comments: 1
We are using our total station to layout ug piping and like to have the invert of the pipe on the point to layout the ditch and verify the invert. Right now my workflow is to place the points in plan ...
Read More | Write Comment

topicsolvedLiner & Duct Insulation Layers Fabrication MEPCAD

May 25, 2023, 17:51:05 PM by Shaun1119 | Views: 104 | Comments: 2
Im trying to figure out how to either shut off insulation (wrap) and leave the liner on. It is spec driven and currently if you shut off the layer it auto assigns the liner and wrap to it shuts both o...
Read More | Write Comment

clipGraphics in Worksheets

May 24, 2023, 15:59:20 PM by RobMiranda1 | Views: 134 | Comments: 2
 Hello
   Does anyone why the worksheet graphics look faded ?
When I print the worksheet the graphics lines look too light or nothing at all
Please see attached image
Read More | Write Comment

xxAdding a service to a Profile

May 22, 2023, 18:07:24 PM by mjohnson7 | Views: 260 | Comments: 9
Hey all,

  I started a project with all the services I needed, and then a CB came out in which a chiller was added. Now I need to add chilled water to the profile, but I can't find the mean...
Read More | Write Comment
Pages: [1]

* Recent Topics

* Recent Posts

Re: Evolve Point on Invert of Pipe by chris4455
[May 27, 2023, 07:19:20 AM]
Re: Fabrication 2024 by Darren Young
[May 26, 2023, 19:01:59 PM]
CID #866 and #1 - Straight Type by ayoung8901
[May 26, 2023, 13:55:54 PM]
Re: Fabrication 2024 by VirtualPilot
[May 26, 2023, 13:46:23 PM]
Evolve Point on Invert of Pipe by welchy78
[May 26, 2023, 13:46:19 PM]

Additional Content